Bell Housing Stuff
The parts shown
below are used in the bell housing.
65 -
93 Pre-Alpha & Alpha One
This is
Quicksilver p/n 26 - 45587 bell housing shift shaft seal. It is pressed into the
bottom of the upper hole in the bell housing on Pre-Alpha & Alpha One
drives. It will also fit Gen II drives Serial # OF094775 and below.
: Order #
5587 for seal only
65 - 93
Pre-Alpha & Alpha One
This is
MerCruiser p/n 23 - 805041A2 bell housing shift shaft seal upgrade kit. It is
pressed into the bell housing on Pre-Alpha & Alpha One drives. It will also
fit Gen II drives Serial # OF094775 and below.
The
large diameter will extend into the exhaust cavity but will have no affect
the exhaust. This upgrade kit now has 2 heavy duty seals installed compared to
the one thin seal shown
The driver is not
included with the kit
The washer is
used to install the top bushing.
The outside
diameter of bushings is 5/8
: Order # 7561
for upgrade kit only
: Order # 9555 for driver &
washer kit
94 & Up Gen II
This is
MerCruiser p/n 23 - 806036A1 bell housing shift shaft seal kit. It
is pressed into the bell housing on 94 & Up Alpha One/Generation II drives
serial # OF094775 and above.
The driver is not
included with the kit.
The outside
diameter of bushings is 3/4
: Order # 7562
for kit only
: Order # 8722 for driver only
88 & Up Bravo
These are shift
shaft parts which fit into the upper housing of Bravo drives.
This is
MerCruiser p/n 23 - 861209A1 upper outdrive shift shaft seal kit. It is pressed
into the upper outdrive housing on all Bravo drives.
The outside
diameter of bushings is 11/16
The bushing kit
comes with the seal but not driver.
: Order # 2709
for seal only
: Order # 7563 for kit only
: Order # 7273 for driver only
This is
Quicksilver p/n 91 - 17275A1 Bravo upper housing shift shaft seal and bushing
installer. It is used to install all of the above bushings and seal into all
Bravo upper housings.
: Order #
7275
65 & Up Side Synthane Washers
These .030 fiber
washer have self adhesive tape on some of them. They stick
onto each inside surface of the gimbal ring and are used as a side thrust
washer for the bell housing. They are sold in a package of 1 each. Order a quantity
of 2 to do both sides.
: Order # 3800 65 &
73 Pre-Alpha - Used With Pull Hinge Pins
: Order # 2498 74 & Up Pre-Alpha & Alpha - Used With Threaded
Hinge Pins
: Order # 1721 for Bravo
: Order # 5401 for TR & TRS ( These are no Longer available, I have 1 left
05/15/13 )
73 - 93 TR & TRS
This is
MerCruiser p/n 26 - 48443 bell housing oil seal. It
is pressed into the bell housing on TR & TRS outdrives. This seals the
outdrive oil going to the reservoir inside of the boat.
Seal is 1 3/8
O.D. by .750 I.D.
Click
here for oil Valves & Hoses
: Order #
5800
88 & Up Gen II & Bravo
This is
MerCruiser p/n 24 - 17997A1 Check Valve kit. It is pressed into the mounting
surface of the upper housing on Alpha One/Generation II and Bravo drives.
This seals the
outdrive oil going to the reservoir inside of the boat.
Click
here for oil Valves & Hoses
: Order #
2715
Click
Here For Prices